Fullspin™ 6-Ball Ceramic XT™ Bearings with Patented High-Precision Built-In Spacer System
Next-level skate bearing tech – more speed, better handling, longer life!
Fit standard 8mm axles only.
Seismic has raised the bar on bearing tech yet again! After the pandemic took out our previous manufacturing partner, we spent over two years nerding out with a crack team of American engineers from one of the biggest and best bearing factories in the world. We scrutinized and re-assessed every last component and design feature – and seized on every opportunity to make refinements both large and small – to fully optimize all aspects of skate bearing performance. That’s why we re-branded the product line as… FULLSPIN. Roll tighter, truer, faster, and smarter on the absolute best skate bearings in the entire history of skate bearings!
6-Ball system with premium-grade Ceramic balls • Exceptionally tight, consistent assembly and raceway tolerances • Extra-tough steel construction • Patented Built-In spacing system and revolutionary alignment precision • High-end lubricant • Labyrinth-style outer seals • Next-level anti-contaminant ball retainers
– Superior speed and acceleration
– More consistent wheel contact and grip
– More predictable slide performance
– Longer wheel and bearing life
6-Ball System: Six larger, stronger balls. Less total friction, better acceleration and speed on straightaways! Recommended for LDP and top-speed pursuits.
Premium Black Ceramic (Si3N4) Balls: Compared to Steel balls, Black Ceramic balls are lighter, smoother, harder, lower in friction, self-lubricating, more heat-resistant, and completely rustproof. These properties combine to increase acceleration and speed… while also scouring and cleaning the raceways. Markedly superior to the White Ceramic balls used in budget Ceramic bearings – formed of Alumina Oxide (Al2O3), those have a higher friction coefficient and don’t dissipate heat as well. Manufactured to Grade G10 spec¹ for truer, lower-friction ball spin inside bearings; less energy loss; more speed; and longer bearing life!
Exceptionally Tight, Consistent Assembly and Raceway Specs: Manufacturing specifications for raceways and assembly are highly technical considerations, but absolutely mission-critical to overall bearing performance. Unlike other skate brands, Seismic fully committed to mastering the science and optimizing every last parameter.
See footnote #2 below for the finer points.² The important takeaway is: Specs as tight and accurate as Fullspin’s are only possible at the very biggest, best-equipped, and most skillful factories in the world – the average small skate bearing producer can’t even come close.
The bottom line for rolling performance: Fullspin’s world-class factory tolerances result in significantly less internal play, friction, wear, and noise; and noticeably superior speed, handling, and durability!
XT (Extra-Tough) Construction: Inner and outer rings precision-machined from superior steel with advanced heat treatment that fully optimizes metal’s crystalline microstructure. Raceways hold strictest curvature and finest surface finish – and bearings stay tight and fast – for far longer!
Outer rings are thicker and 60% stiffer than those seen on most other skate bearings (made with inferior steel). So they resist flexing, spin truer and faster, and keep seals from popping off on extreme impacts.
Radius reduced to bare minimum on all edges of both outer and inner rings – for fuller contact and more stable alignment inside bearing pockets of finer wheels; on axles of finer trucks; and at built-in spacer interfaces. A Fullspin first!
Patented Built-In Spacing System: Fullspin’s patented Built-In spacer interface is quite simply the most advanced bearing alignment tech ever seen in the skate world, full stop. It synergizes with other features to inhibit excess play, friction, wear, and noise; and maximize speed, handling, and durability – far better than any other system.
Fullspin’s integral half-spacers have extra-wide flanged ends (U.S. Pat. #9,126,101) that square up inside wheels with more than double the contact area of ordinary built-in interfaces, for absolutely unparalleled precision and stability. Corrects for off-spec axles and misaligned bearing seats.3 Levels and steadies all working components of seated bearings like no other design, to unleash near-perfectly optimized paired performance.
Built-in spacer lengths calibrated to extra-strict 0.400-inch combined width tolerance, to support highly accurate positioning of paired bearings inside finer wheels with well-engineered hubs.4
Flange components precision-machined from premium bearing steel with advanced heat-treatment for unmatched strength, toughness, and press-fit stability.5
Radius reduced to bare minimum on all edges (ends of flange components and extended inner rings), for fuller contact and more stable alignment at half-spacer interface.
Inner ring bore specs dialed to maintain exceptional straightness on finer axles. Extends 0.5mm on outer (seal) side, eliminating need for washers at hanger and nut interfaces.
Note: The broad Fullspin XT Built-In flange components may not fit hub-less street wheels with old-style, oversized bearing supports – which sometimes leave the wheel’s central hole smaller than the flange (15mm in diameter). For wheels of this type, use Fullspin Classic or Fullspin LITE Built-In bearings.
High-End Lubricant: Packed with premium “high-RPM” light grease from Kyodo Japan. Formulated for peak performance under real-world skating stresses, not max free-spin time. Just press into your wheels and go!6
Note: Free-spinning bearings or wheels by hand, under zero load, is not a meaningful measure of real-world performance (though none of us can resist free-spinning fresh new wheels and bearings). Fullspin’s advanced lubricant is designed to perform best when warmed up under the load of a human skater who’s rolling, turning, and sliding on real asphalt or concrete.7
Outside Seals: Removable rubber-coated “no contact” steel seals with printed graphic. Edges of seals slot inside V-shaped grooves machined into both outer and inner rings. This “Labyrinth” interface maximizes resistance to dust and debris – which can only penetrate the bearing by navigating a twisting, maze-like path around seal edges.
Note: Seals protect bearings from environmental contaminants, which significantly accelerate wear. Properly-made “no contact” seals do not add friction. Brands that promote completely unsealed bearings just want you to wear yours out faster so they can sell you another set (that will also wear out prematurely).
Advanced Dust-Resistant Ball Retainers: Fullspin’s custom ball retainers keep bearings cleaner for longer, without the addition of a second seal. They feature an expanded outer diameter that slots into a groove in the outer ring just like an inside seal would – to form a unique integral barrier against contamination. Molded from an engineering-grade fiber-reinforced composite specifically formulated by the German producer for high stiffness and dimensional stability in bearing retainers and similar components.
ABEC Rating: We don’t bother with the ABEC rating system, which measures only the most superficial dimensional tolerances of the outer and inner rings – all of negligible relevance to real-world skating performance.
Eco-friendly packaging: No wasteful, oversized metal tins or plastic cases – just a minimal recyclable cardboard box. Bearings and spacers wrapped inside VCI (“Volatile Corrosion Inhibitor”) paper – another Fullspin first! Adds superior protection against corrosion during transit and long-term storage of unopened packages.
No imaginary tech, pseudo-science, or smoke-and-mirrors: Just superior performance through genuinely advanced, no-BS engineering; highest-quality materials and components; and highest-precision manufacturing.
100% free of:
• Random bearing tech inappropriately adapted from other industries solely for the sake of novelty.
• High-sounding raceway coatings that interfere with optimal finishing and cause abrasive damage to ball surfaces.
• Flashy lubricant additives that accelerate wear not speed.
• Bombastic references to features and processes like the following – all totally ordinary and unexceptional at any decent, self-respecting skate bearing factory: deep-groove raceways with micro-channels, fine-polishing, fiber-reinforced nylon retainers, hand-inspection, and ultrasonic solvent washing.
1 Compared to balls used in run-of-the-mill skate bearings, G10 specs are 60% – 80% tighter for concentricity (roundness), and 50% – 67% stricter for surface smoothness. (In simpler terms, twice as smooth as the finest cue ball, 10 times as smooth as a mirror finish.)
2 Radial clearance (gap between balls and raceway surfaces) held within a super tight and narrow range, with remarkably little deviation from the exact middle. Synergizes with extra-strict raceway curvature radius for outstandingly balanced load distribution across balls. Raceway surface finish up to 40% smoother than well-known brands. Superior tolerances for outer and inner ring concentricity (roundness), too.
3 Common issues include micro-flaws in axle diameter, axle concentricity, axle straightness, bearing seat levelness, and bearing seat spacing.
4 Oversized built-in spacers seen in some well-known brands prevent at least one bearing in each wheel from fully seating. Wheels are then prone to lurching back-and-forth on the bearing stacks during hard turns and slides – causing inconsistent grip and slide behavior and prematurely-worn bearing pockets.
5 Matching coefficients of thermal expansion ensure extremely secure press-fit between the flange component and the inner ring (machined from identical steel).
6 Do not clean – or add extra lubricant to – brand new Fullspin bearings. Wipe grime off outer seals whenever excess builds up. Clean and re-lube bearings only as needed, depending on how often and where you skate – more frequently if you ride through water, mud, dirt, or sand. Do not remove outer seals or disassemble in any way; just soak in isopropyl alcohol (70% solution or greater), rinse, and let dry. Avoid excessive cleaning, which increases risk of accidental damage to small internal components, as well as citrus-based cleaning solutions, which cause corrosion.
7 Bearings may gain extended free-spin time if they’re under-lubricated, or lubricated with very thin oil, or assembled too loosely. But under real-world skating stresses, they won’t perform as well or hold up as long as high-quality bearings with tight assembly tolerances and appropriate lubricant – even though the latter may have a shorter free-spin. Most skating speed records have been set on bearings with modest free-spin. What matters is how bearings handle under the load of a human rider’s bodyweight – rolling, turning, and sliding on real asphalt or concrete.
